Land Drilling Rig Complete Operation Camp Plus Equipment – 1997 / 2000

Contact the Broker

ID: 7580

REF:
p1cm
Year:
1997
Refit Year:
2000
Flag:
Non US:
Location:
Price:
$5,000,000
Length:
240'
Class:
Details:
Land Drilling Rig Complete Operation Camp Plus Equipment - 1997 / 2000 For Sale

Equipment list:


Drawworks

IDECO model 2100-E (s/n E-78) with 1-1/2" LEBUS grooving, FOSTER type 37-AH / 24-AH air catheads, KOOMEY model CBS-RT2 crown block saver and (2) (GE 752 1000-HP series wound DC motors JANUARY -2012) with 10-HP blower motors fitted with HUNT vertical air cure filters. Last Overhaul: ID/TEC 03/2007 (New brake bands, kicker plates: 01/2008).



Auxiliary Brake

BAYLOR ELMAGCO model 7040W (s/n 10961W) rated @ 78,000 LB-FT torque @ 50 RPM with PWM-20 control system, Drillers control, transformer with EXP rig floor emergency stop unit & emergency stop indicator lamp. Note: Torrington bearing p/n 23040-W-BRC3 (34). New coupling: 12/2005.



Battery Back-Up System

GBC model 18384-205 (s/n 1086): Input 230 VAC for charging - 240 VDC for Baylor brake with SIEMENS 100 AMP, 250 VDC isolating switch and 12 VDC battery 20 N battery bank.



Anti-Collision System

MAN4 HITEC (s/n 038371) AE-1005 power supply unit Kinetic Energy Monitoring System: With control unit (230V input / 28V output), direct-mount encoder (p/n CHHGTX-0004A), Drillers display unit, emergency stop, audible alarm and height & weight sensors. New optical sensor: 01/2008. New drum tracking assy (A000565) and sensor (A000382) 09/2008).



Brake Water Cooling System

O&M model ESH-180-2F8 (unit s/n 151494): Designed for 300 GPM @ 55 DEG C ambient c/w (2) CATERPILLAR 399 radiator coolers (Dolphin 08/2007) with 96" diameter fans each driven by BALDOR 10-HP (575 VAC, 60 Hz, 1760 RPM, EXP), 40-BBL water tank, HALCO SUPREME model 2500 (3" x 2" x 12.5") centrifugal pumps (2) each driven by BALDOR 25-HP (600 VAC, 60 Hz, 1775 RPM, EXP) motor, 3" suction & discharge with check valves & butterfly valves for 100% redundancy. Control panel with starters, switches, run lights. Sensors for: high temperature - low fluid level - low flow.



Top Drive (VARCO Upgrade: 5/2011)

VARCO TDS-11SA VFD - 3D178435-2A1DCE 800-HP 500-TON model with (2) RELANCE -A- 500 VAC (2) 400 HP variable AC electric motors, TWO BLOWERS 5 HP 6OO VOLT FOR COOLING AND 10 HP MOTOR FOR Hydraulics system, All the incoming cables were connected with ex proof pyle national plug. EX PROOF type G3 gearbox (18.61 : 1 ratio), ROSTEL 2-1/2" ID main drive quill (s/n 5-PO06084-1-32701023-1 12/2007) with NC50 RH pin, load nut & load collar (650-T), swivel bail, swivel body, swivel pins & rotary seal. Features: dual directional link tilt, mousehole connection extend, 360 DEG pipe handler, thread compensation, forward & reverse torque limits, drill string torsional dampening, remote-operated 10M PSI WP dual ball valve (mudsaver & safety valve) with remote actuator, power module, mechanical module, cable 145' torque track & torque arrest system, Driller's control panel:



Load nut s/n TDT-GN075620, load collar s/n 253
Valve s/n 4185-SDB-IF-309, remote actuator s/n 4186-TDA-191C
Integrated swivel s/n TDT-RS45747-1-10B (Swivel Bail s/n TDT-RS44848-2, Body s/n 43483, Pins s/n 43483A, 43483B)
Make-up Torque: 55,000 ft-lb. Max Drill Torque: 37,500 ft-lb
Breakout Torque: 75,000 ft-lb. Max Drill Speed: 228 RPM
DS 11SA VFD DRIVE UNIT CONSISTS OF;


INCOMER/ RECTIFIER CUBICLE


1250 AF, LSI, BLIT - IN CB W / UV TRIP

6 PULSE AIR COOLED DIODE BRIDGE RECTIFIER

SURGE SUPPRESSION NET WORK WITH STATUS INDICATERS.

GROUND FAULT MONITOR,

AC LINE REACTOR,

40 AMPS CB FOR 30 KAVA TRANSFORMERS,

80 AMPS CHOPPER UNI.

,

AIR COOLED INVERTER CUBICLE.

DIRECT TORQUE CONTROL W/PROFIBUS COMMUNICATION CARD AND SPEED FEEDBACK ENCORDER CARD,

DC PRE CHARGE CIRCUIT,

INVERTER FAULT INDICATION DISPLAY,

420 KW 600/690 VOLT AIR COOLED VFD MODULESINCULDING MODE FILTERS AND OUT PUT REACTORS,

DC INPUT ISOLATION SWITSH 175 AMPS.



ENCLSURE FOR PLC,

RESISTOR BANK,- EDGE WOUND AIR COOLED RESISTOR.

CONTROL CUBICLE,

60A FUSED SWITCH FOR AUX MOTOR STARTER.

600 VAC AUX MOTOR STARTER.

2 MAVAIER AC UNIT.



Model 11SA with power distribution center (600 VAC, 60 Hz, 3-PH, 1200 AMPS), drive system interconnecting multi-conductors providing interface between Driller's panel, top drive and control electronics and fitted with emergency shutdown:



ABB INVERTER INVO 1 Aand 2,model.
ABB RECTIFIER
SIEMENS PLC PANEL model CPU- 315-2DP (S7-300).
ABB MAIN CIRCUIT BREAKER (600 VAC, 1200 AMP)




Driller's Control Panel VARCO SYSTEM-3D-55701-60-1

BARTEC PROFIX TYPE-073136-4025/0010 EX 11 -2 (1) EEX edm LIAL 11B T4, FNR 5068/09 ,16X DIGITAL INPUT PROF ADDR 08, PART NO- 140698-2

PTB-02 ATEK 1159.

Quill RPM gauge, torque gauge, pipe handler controls, control, mode selection, torque limit controls (forward/reverse), emergency stop. System protection shutdowns.



Mast

DRECO Beam Leg model M-14230-1600 (s/n DHW-253-L153-09/81) NOI inspection: 08/2010: 142'H x 30'W x 1,660,000 LBS (GNC) rated @ 1,200,000 LBS API SHL (12 lines). Racking board capacity: 25,000' (270 stands 5" DP) with 14 stands DC's & INGERSOLL RAND model BU7A-PTAB air winch (s/n BU8690397). Wind rating: 100 MPH full setback, 115 MPH no setback. Raising Line: 2-1/4"D, 6 x 41, EIPS, RRL, IWRC, 145' 6"L w/ open-closed spelter sockets & 132' 6"L w/ open-open spelter (01/2012).

Mast Load off Headache Rack: 140 MT (308,000#).



Crown

DRECO model 860C-742 rated @ 650-T SHL (740-T gross) w/ (7+1) 60"OD x 10"D shaft x 1-1/2" sheaves (Replaced 02/2011).

Casing Stabbing Board

DRECO counter-balanced-adjustable type to API Spec 4E (s/n NDSC-5003): with positive-engaging brake and INGERSOLL RAND model ML500K 0.5-T air winch (s/n 14024) with remote pendant control. Recert: AOTC # 452 (08/2005).



Deadline Anchor

SUPERIOR model E-120 (s/n R-2164) equivalent to DRECO model LOF-100-T: 50-T capacity, 29" diameter, leg mount for 1-1/2" line and MARTIN DECKER type E-80 tension type load cell sensator.



Drilling Line

Powered reel with 5-7/8" diameter shaft and 7,500' of 1-1/2" drilling line to API 9A.



Substructure

DRECO SLINGSHOT (s/n E7-475-579): 33'H x 40'W x 40'L (27' 3" clear height) rated @ 1,200,000 LBS with 800,000 LBS setback load. Drip-pan enclosure for rotary and setback, telescopic/adjustable bell nipple. (1) set 45'L steps, (1) set 25'L steps, handrails, ALLEN GET-AWAY evacuation slide, 6'W x 44'L V-door, 2-piece catwalk (5'W x 60'L x 21"H). Raising Lines (01/2012): 2 x 1-1/2"D x 750'L ungalvanized, 6 x 36 IWRC, 1960 BT, RHO, MBL c/w open spelter socket fitted by resin one end & other end open.



Slingshot Raising System

LANTEC model 4135 (2) hydraulic raising winches (NOV Service: 6/2010): Powered by ABCOR HPU (s/n R10-HU-SWN). LAMPRELL Service: 06/2004, with BALDOR model M4316 (s/n 11/81) (INTERSEL 04/2003) 75-HP motor (575V, 69.6 AMP, 60-HZ, 3-PH, 1760-RPM, EXP), 200-GAL hydraulic tank, local & remote controls.Raising Lines (01/2012): 2 x 2-1/4"D x 132.6'L & 145'L, SWL 47.2 ton, 6 x 36, IWRC, RRL wire rope slings .



BOP Handling System

DRECO 50-TON SWL (s/n 0156101330-1, 0156101330-2): 25-TON SWL hoists (2) (NOV Service: 12/2011), hydraulic rack & pinion with remote control console (powered by ABCOR unit). Raising Lines (09/2011): 2 x 1-1/4"D x 43.5'L, EWL, 6 x 36, IWRC, RHRL wire rope slings w/ 1-1/4" G416 CROSBY open spelter socket both ends.



Doghouse

7'10"W x 7'H x 20'L with lighting panel, Drillers remote BOP station and PETRON remote.Install BOPC CLOSING unit Remote control panel EEGRB08AP- HMI/PLC SIEMENS SIMATIC MULT TOUCH PANEL



Power Control System

ROSS HILL model 1400, 4-bay SCR (s/n 5546/81): (4) AC generator controls (600V, 1445 AMP, 1550 KVA), (4) GE 1600 AMP circuit breakers (CAT # TPR-5616-NOARHC), (4) DC SCR bridges (input: 600V, 1470 AMP AC; output: 750 DC, 1800 AMP DC) with (4) GE 1600 AMP circuit breakers (CAT # TPY-5616), (1) GE 1600 AMP circuit breaker for MCC (CAT # TPRR-561-NRHC), (11) GE 7700 line control center panels (230VAC, 3-PH, 4W, 60-HZ, CAT # 474X0443001), (1) GE 600/220VAC circuit breaker (CAT # TB-43F) for (3) 220VAC transformers, (1) GE 600 VAC circuit breaker (CAT # TJK-436F000) for (1) 460VAC transformer. Main in-coming plug panel with lockouts for DW, MP-1, MP-2 and RT functions.



PCR upgrade by M&I ELECTRIC INDUSTRIES (w/o W834-700-97):

RHCC upgrade: AC control modules (4),
600VAC (primary), 460VAC (secondary) 300KVA xformer for all auxiliary DC drives
Install 0-200 milli-Amp meters from actuators to read kW load sharing: Run mode 1200-RPM, 35-45 mA. Full load 160 Ma.
Install DC Amp meters from generator exciters to read load sharing.
PLC alarm system installed for: (a) engines; low coolant level, high coolant temp, low oil pressure, metal particle detector, generator overspeed, (b) brake-water cooling; low fluid level, high coolant temp, (c) mud pit purge panels (2) for H2S & CH4 (PLC activates alarms via Gaitronics PA system).


SHUNT TO SERIES MOTOR MODFICATION- NOV - JANUARY-2012.


Installed DYNAMIC BRAKE MODEL 1461, DC POWER CABLE AND CONTROL CABLE INTER CONNECTION, SPROKET SLIP PC CARD, HED, VOLTAGE FEED BACK PC CARD , DC MODULE, AND POWER RECPTACLE FOR DC POWER OUT LETS.



Transformers

ROSS HILL CONTROLS type HSUL (3): 600V-127/200Y, 100-KVA, 60-HZ, 1-PH, Cat #100S9XH6C, 4.9% imp, 150 C Temp Rises (s/n 70101-881, 70102-881, 70103-881).
SUNBELT: 600V/480Y/277, 300-KVA, 60-HZ, 3-PH 5.64% imp, 150 C Temp Rise (s/n 22459).
ITC type HTUL: 600V/240Y, 25-KVA, 50/60-HZ, 3-PH, Cat #2832H3DC, 3.6% imp, 150 C Temp Rise, (s/n 726856-10/81).
VICTOR (UAE) model GPTS/100K: 100-KVA, 50/60-HZ, 3-PH, Class H, 115 C temp rise, 600V delta primary, 480V star secondary, 96A primary, 120A secondary, standard IEC726 (s/n 18216/06).
MARCUS type IW: 600V/416/240, 112-KVA, 112-HZ, 3-PH, 3.4% imp, 150 C Temp Rise (s/n 8803-797).


Aux. Brake Controller

BAYLOR model PWM-20 for model 425L Driller's console.



A/C Units (2)

TRANE model TTA120-A300BC, 10-TON single compressor split units.



Cable Grasshopper

8'W x 30'L electric cable tray skid with oscillating cable arm to rig floor and (1 lot) cable trays with covers.



Generators

KATO synchronous, brushless, 2-bearing AC (1500 KW, 347/600V, 1875 KVA, 3-PH, 60 HZ, 0.8 PF, 1200 RPM, 1806 AMP, 90 DEG C temp rise, field volt 100, field AMP 4.3):



Model 1500-685361111 - type 21676 - Cat. #6P7-2050 - s/n 36739-85926-1
Model 1500-685361111 - type 21676 - Cat. #6P7-2050 - s/n 36741-85926-2
Model 1500-680361111 - type 21676 - Cat. #6P7-2050 - s/n 36738-84485-3
Model 1500-680361111 - type 21676 - Cat. #6P7-2050 - s/n 36740-84485-2


DC Motors

GE-752 AND JULIOT series -wound rated at 1000-HP continuous (750 VDC, 1150 AMP, 965 RPM) with Class H insulation, pressurized connection box, auxiliary lockout switch and 10-HP (460 VAC, 60-HZ, 3275 RPM, EXP) blower motors mounted on HUNT model 752V-RHB/LHB vertical air cure filters. Note: Power cable connections are pin type and 20-pin receptacle is PYLE NATIONAL male (p/n ZREP 20332 PN). Refurbished JANUARY 2012



Main Engines (4)



CATERPILLAR series D3512 DITA (4), 1435-HP/1000-KW @ 1200-RPM fitted with WOODWARD EG-10P actuators, injector group 4P 9075, turbo group 12 8187, marine duty air cleaners, SPINNER II oil centrifuges with AMOT metal particle detectors & oil level switch gauges, RACOR primary fuel filters, BICERA crankcase explosion relief valves, 12" exhaust outlets, HMSO protection system for low oil pressure, high water temperature and overspeed air inlet shutoff.


CAT #1 - 3512 Arrangement # 2W 8869 (s/n 67Z 01953)
CAT #2 - 3512 Arrangement # 2W 8869 (s/n 67Z 02173)
CAT #3 - 3512 Arrangement # 2W 8869 (s/n 67Z 02213)
CAT #4 - 3512 Arrangement # 2W 8869 ( s/n 67Z 02212)


Engine Cooling

O&M (drawing # 10569-402) (s/n 1-151426/7/8/9) desert-duty jacket water heat exchangers with updraft design rated @ 150 PSI MAWP (O&M #128156) & converted to standard over-sized water tanks with independent water pump to after-cooler.



Fuel Filtration

ALFA LAVAL model MAB-104B-14/24 (s/n 4118233/2001, f/n 549807-03, p/n 881242-08-14) explosion-resistant solids retaining purifier rated at 500 GPH with motor soft-start panel in NEMA 7 enclosure and combination feed/discharge pump with MARATHON 3-HP, 230/460 VAC, 60-HZ, NEMA 7 motor.



Fuel Tank #1

Crude Settling Tank: 8.5'D x 30'L x 300-BBL (48m3) horizontal, cylindrical on 10'W x 40'L x 3-runner skid with 27" manhole, 2" vent, 4" fill connection, 2" drain, sight-level gauge and 3" x 2" centrifugal transfer pump with 3-HP, 60-HZ, 460VAC motor.



Fuel Tank #2

Clean Crude Tank: 9.8'D x 26'L x 346-BBL (55m3) horizontal, cylindrical on 8'W x 33'L x 2-runner skid with 24" manhole, 2" vent, 4" fill connection, 2" drain and sight-level gauge.



Fuel Day Tank

HEMT 50-BBL (7.5m3) skidded crude day-tank: With ROPER type 1 gear transfer pump driven by 3-HP 460V 60-HZ motor.



Diesel Tank

HEMT 60-BBL (10m3) rectanguler (s/n A318-2333) on 19.7'L x 8.2'W x 5.9'H skid with fuel filtration unit and ROPER type 1 gear transfer pump driven by 3-HP 460V 60-HZ motor.



Air Compressors (2)

GARDNER-DENVER model EDFQLC (s/n R-00329, R028331), oil-injected, rotary screw type rated @ 309 SCFM (each) @ 125 PSI driven by model 24CA-3240 AC motor 75-HP, 575VAC, 60-HZ (s/n 97600010, 97600011) inside high ambient NEMA 4 enclosure (spare air-end common for Rigs-10/31/32).



Cold-Start Compressor #1

ATLAS-COPCO model XA-125 (s/n AIA-0133963): 55.5 KW, 2800-RPM ATLAS COPCO.


Air Dryer (2008)

GREAT LAKES model GPS-1000-N4-116 (s/n 31303) heatless, regenerative dessicant (p/n 692001) type, 1000 SCFM flow @ 100 PSIG with ASME coded twin towers rated @ 150 PSIG, solid state timer, pilot air filter, 110V NEMA 4 control, model GC-1000-SA coalescing pre-filter and model GP-1660 particulate after-filter.



Vertical Air Receivers (3)

SILVAN INDUSTRIES: 36" diameter, 400 GAL each, 200 PSI MAWP with relief valves set @ 130 PSI (s/n 233187, 233194, 233197).



Horizontal Air Receivers (2)

36" diameter, 400 GAL each, 200 PSI TP with relief valve set @ 130 PSI.



Air Hoist: INGERSOLL-RAND type FA2.5-16M rated @ 2.5-T SWL (s/n 73185)new installed 02/2012.

Air Hoist: INGERSOLL-RAND type FA5-MR24MK1G rated @ 4.5-T SWL (s/n A017075) new installed 02/2012.

Man Rider: INGERSOLL-RAND type FA150KGI/05105 rated @ 150-KG (s/n KQ004254)

Air Hoist: INGERSOLL-RAND BU7A-PTAB rated @ 0.5-T SWL (s/n BU8690397)

Air Hoist: INGERSOLL-RAND ML-500K (stabbing board) rated @ 0.5-T SWL (s/n 14024)

Air Hoist: INGERSOLL-RAND type UW-702 (spare) rated @ 0.5-T SWL (s/n SRG-17002)





Mud Pumps (2)

1.EMSCO Model T-1600 triplex, 7-1/2" bore x 12" stroke (s/n 74, 102) with SOUTHWEST style 2-piece forged fluid ends (p/n KOP FEMT1316SUCSW, FEMT1316DISSW), IDECO unitized V-belt pump drive, HYDRIL type K-20 5M WP pulsation dampener (RX-39), suction/discharge strainers, 0-10M PSI pressure gauge, FALCON type C flanged RRV (1,500-5,000 PSI operating range), DEMCO 2" 5M WP bleed-off valve, HALCO type S (1-1/2" x 2"R x 8-1/2") centrifugal liner wash pump (s/n 04181) with MARATHON 3-HP EXP motor. Each pump powered by (2) GE-752, 1000-HP seres-wound DC motors with 10-HP blower motor (JANUARY -2012) mounted over HUNT vertical air cure filter. Power ends fitted with dual electric & mechanical lube system.

S/N 74: New bull gear & pinion (02/2004). New bearings main/pinion (08/2007)

S/N 102: New bull gear, pinion, eccentric & crosshead bearings (03/2005)



Mud Pump (1)

LOADMASTER model LMF-1600 triplex, 7" bore x 12" stroke (s/n LMF-101) with single piece forged fluid ends, metal to metal liner lock system, self-aligning rids with dual tube rod clamps, unitized V-belt drive (8/8VP3000 Kevlar V-belts), model KB-75 5M WP pulsation dampener (RX-39), suction/discharge strainers, 0-40,000 kPa pressure gauge, RETSCO 3" type C flanged RRV (1,500-5,000 PSI operating range), 2" 5M WP bleed-off valve, liner wash pump (1" x 1-1/2") with 3-HP EXP motor (230/460V, 3-PH, 60-HZ), powered by (1) GE 752 1000-HP series -wound DC motor(A) JOULIOT 1000 HP SERIES WOUND DC MOTOR (B) (JANUARY 2012)each with 10-HP blower motor mounted over HUNT Air Cure filter. Power end fitted with triple redundant lube system: Internal splash/gravity feed, internal gear-driven pump, external gear pump driven by 480V, 3-PH, 60-HZ EXP electric motor and pressurized lubrication to lower crosshead slides.



Centrifugal Pumps (5)

HALCO model 2500: 8" x 6" x 14" w/ 100-HP (600VAC, 60-HZ, 1200 RPM, EXP) motors: (2 mud mixing w/ 14", mud transfer w/ 13.5", desander w/ 14", mud cleaner w/ 14").



Centrifugal Pumps (2)

HALCO model 2500: 8" x 6" x 12" w/ 40-HP motors (600VAC, 60-HZ, 1775 RPM, EXP): Charging pumps/degasser.



Centrifugal Pumps (3)

HALCO model 2500: 3" x 2" x 13" w/ 20-HP motors (600VAC, 60-HZ, 1775 RPM, EXP): (2 water transfer w/ 10", trip tank w/ 10.5").



Centrifugal Pumps (2)

HALCO model 2500: 3" x 2" x 12.5" w/ 25-HP (600VAC, 60-HZ, 1775 RPM, EXP) motors: (brake water cooling).



Centrifugal Pumps (2)

HALCO model 2500: 1-1/2" x 2"R x 8.5" w/ 3-HP (230/460VAC, 60-HZ, 1800 RPM, EXP) motors: (liner wash).



Centrifugal Pump (1)

MISSION SUPREME: 5" x 6" x 11" w/ 60-HP (600VAC, 60-HZ, 1800 RPM, EXP) motor: (recycle).



Centrifugal Pump (1)

BAKER MUD HOG Series 250 (s/n 0329): 5" x 6" x 11" w/ 60-HP (600VAC, 60-HZ, 1800 RPM, EXP) motor: (recycle).



Cellar Pump

FLYGHT PUMP(2) Motor model-3217090 - S/N-950057 & 1302-08,RPM-1745,10-HP,3 PHASE- 460 VOLT/ 60 HZ.



Suction Tank

10'W x 7'H x 50'L x 490-BBL capacity on 60'L, 3-runner skid with 8' covered extension over mixing pumps.



Intermediate Tank

10'W x 7'H x 40'L x 450-BBL capacity: Mounted on 42'L, 3-runner skid.



Shaker Tank

10'W x 7'H x 50'L x 550-BBL capacity on 60'L, 3-runner skid with 5' covered extension each end over desander & desilter pumps.



Reserve Tanks (2)

10'W x 7'H x 34'L x 400-BBL capacity (each): Mounted on 45'L, 3-runner skids.



Suction Valves

PATCO lever-operated type: 8" PMF-8LFT (1), 8" PMF-8LSTD (1), PMF-10LFT (2), PMF-10LSTD (1). DEMCO butterfly valves: 12"-10"-8"-6"- 3".



Agitators (7)

BRANDT model MA-25 (s/n 8005431418-00-01/02/03/04/05, 8005348597-00-04/05): With 25-HP (600V, 60-HZ-3-PH, 1765-RPM, fRAME 284T, EXP) AC motors and (3) 44"W x ½"D canted impellers. New Agitators Installed: 12/2005.



Agitators (3)

BRANDT model MA-15 (s/n 81177, 44427776/7): With 15-HP (600V, 60-HZ, 3-PH, 1175 RPM, Frame 284T, EXP) AC motors plus one spare (WHS).



Trip Tank

7'9"W x 7'4"H x 10'L x 6m3 capacity on 20'L, 3-runner skid with 5' covered extension each end over degasser & trip tank pumps and 60cm/stand (5" DP).( 40 HP 600 VOLT 60 HZ MOTOR)



Shale Shakers (3)

BRANDT King Cobra (s/n K-1336-N, K-1339-N, K-1334-N) fine screen adjustable LM with 3.5 - 7.0 G operating vibration level and MARTIN type TENV vibrator motors: 2.4-HP, 440/480V, 3-PH, 60-HZ, 1800-RPM, 3.5 AMP, Frame 70-CDX18-8340-VM (p/n 01-2054)



Mud-Gas Separator

SWACO (Fabricated by al-hajiry on 2009) (s/n SW-100/5515), 48" OD x 6" inlet x 8" outlet w/ 1m3 stripping tank. Rated design capacity: 1500 GPM (liquids) - 5 MMCFD (gas), 125 PSI WP @ 600 DEG F, 188 PSI TP.



Degasser

BRANDT model DG-10 with vacuum air compressor driven by TOSHIBA 5-HP (230/460 VAC, 60-HZ, 1730 RPM, EXP) motor (s/n 97410983).



Desander

BRANDT model 3T12, 3 x 12" cone driven by HALCO model 2500 6" x 8" x 100-HP x 1200 RPM x 1200 GPM centrifugal pump.



Mud Hoppers (2)

HALCO model 1050-20: 6" hi-shear/low-pressure, 2" nozzle, venturi, funnel, sack table, 6" butterfly valve, 3" male NPT inlet, 6" WN outlet (Mix capacity (each): 800-900# barite p/m.



Mud Shearing

VORTEX VENTURES model LOBESTAR shear/mixer (p/n VVE-U-6S) eductor with 6" housing, jet nozzle insert & conical diffuser insert and hopper. In Service: 12/2005.



Mud Testing

Digital precision balance 0.01-400 grams (p/n 166-03), rheometer heating cup (p/n 130-38-1), FANN model 140 mud balance, HAL TRU-WATE cup, OFI viscometer (s/n 03-758), LAMOTTE portable turbidity meter (p/n 299-10), PYKNOMETER calibrated barite density meter (p/n 153-49), FANN model 35-SA 6-speed viscometer, 230-115V transformer, 230V 10 ml oil/water retort kit, API filter press, HPHT 175 ml filter press (sgl CO2 230V), sand content kit, portable digital PH meter, chloride-alkalinity water hardness kit, GARRET gas train (H2S/CO2), H2S detection kit (copper method), MBT kit (230V), HAMILTON bench mixer w/ container (230V), WISCONSIN model UM200 convection oven (220 DEG C max).



Sack Handling

LIFT-MOORE model MZ4-6A hydraulic crane (s/n B460T4L) with 1-MT SWL, 10'-16' extending boom (with 360 DEG rotations) powered by HPU with 2 x 6 GPM hydraulic pumps.



Water Storage Tank #1

10'D x 36'L x 500-BBL horizontal cylindrical on 3-runner skid with HALCO model 2500 3" x 2" x 10" centrifugal transfer pump and 20-HP motor (600VAC, 60-HZ, 1775 RPM, EXP).



Water Storage Tank #2

9'D x 21'L x 240-BBL horizontal cylindrical on 2-runner skid with HALCO model 2500 3" x 2" x 10" centrifugal transfer pump and 20-HP motor (600VAC, 60-HZ, 1775 RPM, EXP).



Mud Lines & Manifold:

Gate Valves (6): DEMCO 5" 5M WP
Gate Valves (4): DEMCO 3" 5M WP
Gate Valves (4): DEMCO 2" 5M WP
Gate Valves (1): DEMCO 4" 5M WP
Plug Valves (4): 2" 10M WP with Fig.1502 unions (cement manifold)
Mud Gauges (2): OTECO 0-6000 PSI
Bleed-off Choke: CIW 2-1/16" 5M WP manual choke
Transmitter Flange: PETRON instrument flange with Fig.1502 misaligning unions
Dual Standpipes: 4"ID 5M WP x 160 DEG goosenecks with Fig.1002 top unions
Cement Standpipe: 2" x 12m x 10M WP with flexible hose
Dual Sub Lines: 5" 5M WP with Fig.1002 unions
Dual Kill Lines: 2" XXHVY 10M WP




HP Hoses - Standpipes to TDS Swivel (2): ROTARY API grade D, 3-1/2"x 4" x 75' x 5M WP with KEMPER 4" Fig.1002 male-female unions (s/n 30108-02)

HP Hoses - Sub Base to Standpipe Manifold (3): DAYCO API grade D, 3-1/2" x 30'L, 5M WP with butt-welded KEMPER 4" Fig.1002 unions male x female unions.

HP Hoses - Mud Pumps to Sub Base to Standpipe Manifold (5): TAURUS API grade D, 3-1/2" x 13'L, 5M WP with butt-welded KEMPER 4" Fig.1002 male / female unions.



ROBSCO API grade D, 32NH x 60'L, 5M WP with butt-welded KEMPER 2" Fig.1002 male x female unions

ROBSCO API grade D, 32NH x 30'L, 5M WP with butt-welded KEMPER 2" Fig.1002 male x female unions

ROBSCO API grade D, 32NH x 13'L, 5M WP with butt-welded KEMPER 2" Fig.1002 male x female unions





Rotary Table

IDECO model 375-E (s/n 176): Rated bearing deadload capacity 700-T. Rated rotating load 434-T. IDECO model T-2 2-speed gearbox (s/n 5305900), GE-752 1000-HP series -wound DC moto (JANUARY 2012) with 10-HP (460VAC, 60-HZ, 3275 RPM, EXP) high-output blower motor mounted over HUNT vertical air cure filter. Last Service: ID/TEC 09/2005.



Master Bushing (2)

CAM-TECH model MPCH (s/n NDSC-5236) & (spare) VARCO model MPCH (s/n R-2157): 37-1/2" pin drive c/w API bowls (#1-2-3), 4-leg & 2-leg slings, bit breaker adapter plate.

In Service: 01/2007.



Kelly Bushing: VARCO model HDP (s/n R31-001-5473) w/ JT OILFIELD safety guard.



Hook-Block

IDECO Shorty model UTB-525-6-60 (s/n 618): 525-T API rating with unitized hook and (6) 60" OD x 1-1/2"D grooved sheaves. Hang-off sling: 1-1/4" D x 114'L. NOV Service: 02/2010.



Hook-Block (Backup)

NATIONAL model 660-G500 (s/n T-2598): 500-T API rating with unitized hook (s/n HT-714424) and (6) 60" OD x 1-1/2"D grooved sheaves. NOV Service: 02/2010.



Swivel

NATIONAL OILWELL model P-500 (s/n T-5268): API 500-T rating with 5M PSI WP - 15 DEG API angle gooseneck, 4" Fig.1002 union, 7-5/8" LH REG connection and spare washpipe assy (p/n 703429-G1U).



Swivel (Backup)

NATIONAL OILWELL model P-500 (s/n 43457N): API 500-T rating with 5,000 PSI WP - 15 DEG API angle gooseneck, 4" Fig.1002 union, 7-5/8" LH REG connection and spare washpipe assy (p/n 703429-G1U).



Kelly Spinner

VARCO type 6600 pneumatic (s/n 6D15X545): With (1) motor for RH/LH rotation, control lines, foot valve and 6-5/8" REG LH box-up/pin-down.



Kelly

INTER DRILL 5-1/4" hexagonal, 6-5/8 REG LH box x 4-1/2 IF pin (6-3/8" OD x 2-13/16" ID) x 40'L x 37' working length (s/n K5BA004).



Drillpipe (2698m)

5" OD, G-105, 25.6 PPF, R-II, 4" ID, IEU with 6-1/2" OD x 2-3/4" ID x 4-1/2-IF, 18 DEG tool joints, TK-34 IPC and ARNCO 100XT hard banding.



Drillpipe (2951m)

5" OD, G-105, 19.5 PPF, R-II, IEU with 6-1/2" OD x 3-1/4" ID x 4-1/2-IF, 18 DEG tool joints, TK-34 IPC, ARMORCOR M hard banding.



DP Pup Joints: to suit 5" grade G-105 drillpipe (2 each: 1.5m, 3m, 4.5m).



HWDP (42)

5" OD x 3" ID, 6-1/2" OD x 3-1/16" ID tool joints (24"L box, 30"L pin), 18 DEG taper, API BBB/SRG, 4-1/2 IF, TK-34 IPC, ARMORCOR M hard banding.



Drill Collars (13): Spiral 9-1/2" x 3", slip recess, 7-5/8 REG, API BBB/SRG

Drill Collars (27): Spiral 8" x 2-13/16", slip recess, 6-5/8 REG, API BBB/SRG

Drill Collars (11): Spiral 8-1/4" x 2-13/16", slip recess, 6-5/8 REG, API BBB/SRG

Drill Collars (26): Spiral 6-1/2" x 2-13/16", slip recess, 4 IF, API BBB/SRG

Drill Collar Pony: SMFI 1.25m, 4.5m (WHS)



IBOP: PACKARD 10M WP, 4-1/2 IF



Float Sub (2): 7-5/8R x 7-5/8R x 9-1/2" x 3" bored for 5F-6R (s/n X9BB001/002)

Float Sub (2): 7-5/8R x 6-5/8R x 9-1/2" x 3" bored for 5F-6R (s/n X9BB003/004)

Float Sub (2): 6-5/8R x 6-5/8R x 8" x 2-13/16" bored for 5F-6R (s/n X8BB001/003)

Float Sub (2): 4-1/2R x 4 IF x 6-1/2" x 2-13/16" bored for 4R (s/n X6BB002/001)

Float Sub (1): 3-1/2R x 3-1/2 IF x 4-3/4" x 2-1/4" bored for 2F-3R (s/n: X4BB006)



Float Valves (3): BAKER model F: Spring type, size 5F-6R

Float Valves (3): BAKER model F: Spring type, size 4R

Float Valves (1): BAKER model F: Spring type, size 2F-3R

Float Valves (1): BAKER model G: Flapper type, ported, size 5F-6R

Float Valves (1): BAKER model G: Flapper type, ported, size 4R

Float Valves (1): BAKER model G: Flapper type, ported, size 2F-3R



Circ. Head (2) (s/n X6CH001/002): KING w/ WECO 2" 1502 male swivel x 4-1/2 IF Pin

Circ. Head (1) (s/n X4CH001): KING w/ WECO 2" fig.1502 male swivel x 3-1/2 IF Pin



UPR Kelly Cock: PACKARD 15M 7-3/4" OD x 2-13/16" ID x 6-5/8R LH (s/n KCBA005)

UPR Kelly Cock: HYDRIL 15M 7-3/4" OD x 2-13/16" ID x 6-5/8R LH (s/n KCBA006)



LWR Kelly Cock: HYDRIL 15M 6-5/8" OD x 2-13/16" ID x 4-1/2 IF (s/n KVBA011)

LWR Kelly Cock: HYDRIL 15M 6-5/8" OD x 2-13/16" ID x 4-1/2 IF (s/n KVBA012)

LWR Kelly Cock: PACKARD 10M 5-3/8" OD x 2-1/8" ID x 3-1/2 IF (s/n KVL04)

LWR Kelly Cock: PACKARD 10M 5-3/8" OD x 2-1/8" ID x 3-1/2 IF (s/n KVL05)



Substitutes:

7-5/8 REG pin x 4-1/2 IF box (3 each: S/N X9BA001/003/004)

7-5/8 REG pin x 6-5/8 REG box (5 each: S/N X9BA007/008/011/012/013)

7-5/8 REG box x 6-5/8 REG pin (1 each: S/N X9BA009)

7-5/8 REG box x 7-5/8 REG box (4 each: S/N X9BB001/002/003/004)

6-5/8 REG pin x 4-1/2 IF box (4 each: S/N X8BA002/010/011/012)

6-5/8 REG pin x 4 IF box (3 each: S/N X8BA004/007/017)

6-5/8 REG BOX x 6-5/8 REG box (2 each: S/N X8BB001/003)

4 REG box x 4-1/2 IF pin (1 each: S/N X6BA008)

4-1/2 IF pin x 4 IF box (4 each: S/N X6BA001/012/016/017)

4-1/2 IF box x 4 IF pin (2 each: S/N X6BA018/014/019)

4-1/2 IF box x 3-1/2 IF pin (1 each: S/N X6BA005)

4-1/2 IF pin x 4-1/2 IF pin (1 each: S/N X6PP001)

4-1/2 REG pin x 4 IF box (1 each: S/N X6BA008)

4-1/2 REG box x 4 IF box (2 each: S/N X6BB001/002)

4-1/2 IF box x 4 IF box (2 each: S/N X6BB010/011)

3-1/2 IF box x 3-1/2 EU pin (1 each: S/N X3BA001)





DC Lift Subs (05): 7-5/8 REG x 9-1/2" OD with 5" OD neck

DC Lift Subs (10): 6-5/8 REG x 8" OD with 5" OD neck

DC Lift Subs (16): 4 API IF x 6-1/2" OD with 5" OD neck



Elevator Links: VARCO 2-3/4"D x 132"L x 350-T (s/n 369L/R)

Elevator Links: DENCON 3-1/2"D x 132"L x 500-T (s/n 97681CL/R)

Elevator Links: VARCO 2-3/4"D x 108"L x 350-T (s/n LR10-01/02)

Elevator Links: VARCO 3-1/2"D x 192"L x 500-T (s/n 22L/22R)

Hydraulic Cathead

DRILCO model D (s/n MD46052) coupled to 10-HP (600VAC, 60-HZ, 1750-RPM) motor.



DP Spinning Wrench: CAM-TECH model SSW-40 (s/n 081805-C-164).



DP Slips (1): CAM-TECH model AS-16 with segments for 5" DP (s/n P/N-C-AS16-5550)

DP Slips (1): DEN-CON type RDL extra long for 5" DP (s/n 7098)

DP Slips (1): DEN-CON type RDL extra long for 3-1/2" OD (s/n 15522/32)



DP Tongs (2): VARCO type HT-100 with lug jaws to 11" OD (TA-16450/16455)

DP Tongs (2): VARCO type HT-65 with lug jaws to 8.5" OD (s/n TA277/280)



DC Slips: DEN-CON type LDC 9-1/4" - 11-1/4" OD (s/n 6904)

DC Slips: DEN-CON type LDC 8-1/2" - 10" OD (s/n 6906)

DC Slips: DEN-CON type LDC 6-3/4" - 8-1/4" OD (s/n 6689)

DC Slips: DEN-CON type UDC 5-1/2" - 7" OD (s/n 6902/6903)

DC Slips: DEN-CON type UDC 4-1/2" - 6" OD (s/n 6899)

DC Slips: DEN-CON type SDC 4" - 4-7/8" OD (s/n 6898)



DP Elevator: VARCO-BJ type GG-CL 350-T for 5" OD DP (s/n NL0112261)

DP Elevator: VARCO-BJ type GG-CL-350 350-T for 5" OD DP (s/n NL71889)



DC Safety Clamp: VARCO type MPR with box end wrench (9-1/4" - 10-1/2" OD)

DC Safety Clamp: DEN-CON type MPR with box end wrench (10-1/2" - 11-1/2" OD)



API Bowl Inserts: #1 (11-3/4" - 13-3/8"), #2 (9-5/8" - 10-3/4"), #3 (3-1/2" - 5-1/2")



Mud Bucket: OTECO type MG-600 with 4" outlet, dressed for 5" OD DP

Bit Breakers: 17-1/2", 12-1/4", 8-1/2", 6-1/8"





API Casing Drifts: 20" x 197.9 kg/m, 13-3/8" x 107.2 kg/m, 13-3/8" x 81.1 kg/m, 9-5/8" x 79.6 kg/m, 7" x 52.1 kg/m, 5-1/2" x 34.3 kg/m



Circulating Swages: WECO 2" fig.1502 male x 20"(2) BTC,13-3/8"(3)BTC,9-5/8"(2) NVAM/V-TOP.



Casing Tongs: FOLEY type FD55 with jaws to 17-1/2" & one to 21-1/2" (s/n 5472B/F)



Casing Bushing: VARCO type CUL for 20"



Pin Thread Protectors: KLAMPON type for 13-3/8", 9-5/8", 7", 5-1/2"



Casing Slips: DEN-CON type CL for 13-3/8" (s/n 6993) with 18 segments

Casing Slips: DEN-CON type CL for 9-5/8" (s/n 6994) with 14 segments

Casing Slips: DEN-CON type CL for 7" (s/n 7031) with 12 segments

Casing Slips: DEN-CON type RDL 5-1/2" x 5-1/2" XL for 5-1/2" (s/n 7098)









Bag Preventer

HYDRIL type GK (s/n R-3105): 13-5/8" bore x 5M WP w/ 13-5/8" 5M WP studded top (BX-160) x 13-5/8" 10M WP (BX-159) flanged bottom, f/w 5-GAL surge bottle.

WESCO Recert: 12/2009.



Ram Preventer

T3 Energy single type U (s/n CO1601542,NDSC 5240): 13-5/8" bore x 10M WP w/ 13-5/8" 10M WP (BX-159) flanges & 4-1/16" 10M WP (BX-155) side outlets d/w standard bore bonnets. T3 Energy Services Recert: 12/2009.



Ram Preventer

T3 Energy double type U (s/n CO1601543,NDSC-5241): 13-5/8" bore x 10M WP w/ 13-5/8" 10M WP flanges and 4-1/16" 10M WP (BX-155) side outlets d/w standard bore bonnets over large-bore shear bonnets fitted with dual tandem shear boosters. CIW Recert: 12/2009.



Rams (CIW Super Trim):

1 set: 9-5/8" (s/n R-3192)
2 sets: 5" (s/n NDSC-5268)
1 set: VBR 2-7/8" - 5" (WHS)
1 set: VBR 4-1/2" - 7" (s/n NDSC-5011A/B)
1 set: SBR (s/n NDSC-5220A/B)
1 set: Blind Rams (s/n R-3096)


Adapter Spool (s/n NDSC-5276): 13-5/8" 10M WP (BX-159) flg x 13-5/8" 5M WP (BX-160) hub (f/ hubbed bag)



Jetting Sub

DRILCO 6-3/8" OD x 2-1/2" ID x 22"L x 4-1/2 IF (AISI 4145) with 1/2" ports.



BOP Test Pump

VALVCON unit-mounted 10M WP model SSR-15 (s/n R-2153): Stand-mounted chart recorder with high-pressure test hose & recorder hose. Rebuilt: 03/2007.



BOP Test Pump

PROSERV type 100 (s/n 0290-03-2004), dual pump system with HASKEL ASF-B-10 (s/n 204-357/1003-679) & ASF-150 air pumps, DEWIT model 4888SS chart recorder (s/n 04-00501-2-01) w/ instrument panel in skidded stainless steel enclosure. In Service: 04/2004.



BOP Cup Tester: 4-1/2" IF type F. Cups: 13-3/8" (54.5-72ppf), 9-5/8" (43.5-53.5ppf)

BOP Cup Tester: 3-1/2" IF type F. Cups: 7" (26-38 ppf)

BOP Test Stump

13-5/8" 10M WP (BX-159) with inconel-lined ring grooves, 4-1/2-IF box, 9-1/16" autoclave bleed & test port, mounted on L-frame master skid (s/n R-2168). Recert: 04/2008.



Kelly Cock Test Sub # 1: 6-1/2" OD with 4-1/2 IF box by 2" Fig.1502 (s/n X6TS001).

Kelly Cock Test Sub # 2: 4-3/4" OD with 3-1/2 IF box by 2" Fig.1502 (s/n X4TS001).



BOP Kill Line (H2S trim)

DSA (2): 4-1/16" 10M WP (BX-155) x 2-1/16" 10M WP (BX-152).
HCR #1: ANSON type E (s/n 171654), 2-1/16" bore, 10M WP (BX-152) w/ double-acting hydraulic actuator & manual locking screw.
HCR #2: CIW type FLS (s/n NDSC-5258), 2-1/16" bore, 10M WP (BX-152) w/ double acting hydraulic actuator & manual locking screw.
MGV #1: ANSON type E (s/n 171463), 2-1/16" bore, 10M WP (BX-152).
MGV #2: CIW type FLS (s/n 11030142-06), 2-1/16" bore, 10M WP (BX-152).
Check Valve #1: EEC type E-MS (s/n NDSC-5264), 2-1/16" bore, 10M WP (BX-152).
Check Valve #2: CIW type MS (s/n NDSC-5217), 2-1/16" bore, 10M WP (BX-152). .
Armored Hose: 2" x 30' fire-resistant, 2-1/16" 10M WP (BX-155) (New: 04/2008).
BOP Choke Line (H2S trim)
HCR #1: MCM type FC (s/n NDSC-5257), 4-1/16" bore, 10M WP, (BX-155) w/ double- acting hydraulic actuator & manual locking screw.
HCR #2: CIW type FLS (s/n 9765), 4-1/16" bore, 10M WP (BX-155) w/ double-acting hydraulic actuator & manual locking screw.
MGV #1: CIW type FLS (s/n NDSC-5256), 4-1/16" bore, 10M WP (BX-155).
MGV #2: CIW type FLS (NDSC-5262), 4-1/16" bore, 10M WP (BX-155).
Armored Hose: 4" x 35'L, fire-resistant, 4-1/16" 10M PSI WP (BX-155). Recert: 03/2008.


BOP Make-Up

HI-FORCE model TWH54 double acting, reversible ratchet, hydraulic torque wrench (Range: 395-3,950 lbf.ft) with 2-15/16" ratchet head and HI-FORCE model HTWP3140P-A, 2-speed, air-driven hydraulic pump.



Choke Manifold

CIW (s/n 00-1293) 10M WP (11) valve, H2S trim: EEC Ultraflow type E-C 3-1/16" 10M WP (BX-154) hydraulic drilling choke with control panel (see below), J-2 transmitter flange and EEC style H-2 3-1/16" 10M WP manual choke. WESCO Recert: 10/2007.

MGV (1): CIW model FC 2-1/16" 10M WP, BX-152
MGV (6): CIW model FC 3-1/16" 10M WP, BX-154
MGV (2): CIW model FC 4-1/16" 10M WP, BX-155
MGV (1): CIW model FC 4-1/16" 5M WP, RX-39
MGV (1): CIW model FC 3-1/8" 5M WP, RX-35


Choke Control Console (2008)

MCM (CIW style) with digital pump stroke counter, 0 - 40,000 kPa drill pipe pressure gauge,

0 - 70,000 kPa casing pressure gauge, choke position indicator, choke speed adjustment switch, hydraulic fluid supply with back-up hand pump, hydraulic pressure gauge and limit switches-brackets-clamps for two pumps.



(Spare Choke Control Console) VALVCON (CIW style) with EEC digital pump stroke counter, 0 - 40,000 kPa drill pipe pressure gauge, 0 - 70,000 kPa casing pressure gauge, choke position indicator, choke speed adjustment switch, hydraulic fluid supply with back-up hand pump, hydraulic pressure gauge and limit switches-brackets-clamps for two pumps.



BOP Closing Unit

BOPC DCS TM 9 STATION CONTROL SYSTEM CORDYNE INDUSTRIAL MOTOR AND DRIVES 330-2K50-E40GD-U23M-6-1 (s/n 6131): 330-GAL 6-station with 400-GAL reservoir, (22) NIPPON 15-GAL accumulator bottles, (2) GRACO model 208-003 type K-50 air pumps (45:1 ratio, 3.3 GPM each, s/n A5535), GARDNER-DENVER model PS-172 triplex (type UET40-HTHT-600) with WEG40-HP explosion proof motor (460 VAC, 1770 RPM). GPES Recert: 12/2005.



Accumulator: Model TB3305B.
Manifold: Model UMGT2R06P10 hydraulic w/ 1", motor-driven, failsafe regulator
TR Regulator (auto): Model PTR-5-1500-0-10 (s/n 9018)
TR Regulator (manual): Model MTR-5-1500-0-10 (s/n 04020)
Driller's Remote: Model AOGPR006-FC, 6-station air-operated w/ open/close display
Toolpusher's Remote: Model EE GRB08AP-HMI/PLC SIEMENS TOUCH PANEL
Air Inter-connect Cable Assy: Model 100-JG37JG
Air Shuttle Valve Assy: Model SV12SV19 (operates 4-way c/valve - both remotes)
Low Pressure Alarm: Model LHP - Low Fluid Level Alarm: Model LFL
Pipe Rack Assy: Model PRMG40-13 32'L with 15 x 1" x 6M WP steel control lines
Control Hoses: Spec. 070-5000 5M WP S/S armored (10 x 34'L, 2 x 38'L, 12 x 8'L)


Chiksans (6): FMC "LSG" 10 style 50 and style 10 fig 1502, 2" x 12' loops.





Driller's Console

PETRON model IDS-2000 RIG SITE MONITOR with Pentium-based computer, 1.4 KVA UPS (2), remote printer and display with graphics printout and DRILGRAPH remote. Sensors for active pits (5) including: PVT, trip tank, flow-out, pump SPM, TD, ROP, bit tracking, pipe velocity, hook load, WOB, pump pressure, rotary RPM, rotary torque. IDS indicator model HKL-A000063. IDS indicator sensor model P000010 (2).



Weight Indicator:

PETRON type EB (16") model AWE9-1 (s/n 0325).
MD-TOTCO type EB (16") series AWE (s/n 1024).
PETRON type E80 (s/n M2073) 'tension' type sensator.
MD-TOTCO type E80 (s/n 0202309) 'tension' type sensator.


Hydraulic Analog Gauges/Sensors: for tong torque, pump PSI, flow indicator, trip tank



Auto Driller

MATTCO BEARCAT (s/n 8036): with pneumatic controller and feedback.



Drift Recorder

MARTIN DECKER-TOTCO 8 DEG & 16 DEG: double recorders c/w accessories.



COOLING UNITS. Port.a.cool portable evaporative cooling units -series 2000 install on the RIG FLOOR AND RESERVE TANK.



PA system

ATKINSON DYNAMICS INTERCOMS MODEL AD 26-8 GAITRONICS Page-Party with 12-stations (rig floor/choke manifold/shaker tank/suction tank, workshop, offices [3], SCR/substructure/guard cabin/elect store) and tied in with the PLC via a tone generator for CH4, H2S and enginge control audible alarms.



Monkey Board PA

ATKINSON DYNAMICS INTERCOMS MODEL AD26-8: For Driller-Derrickman with type hands-free remote at monkey board.


Rig Workshop

TOES design 3-section Mechanic/Welder workshop, store & cool-store on 3-runner skid. Each section: 10mL x 3.2mW x 3.2mH with roof and 2-TON SWL lifting beams over Welder's workshop. Includes small air receiver and:

Electric Welding Set (Unit s/n NDSC-5251): MILLER Gold Star (s/n 602) 450 AMP
Diesel Welding Set (Unit s/n NDSC-5247): MILLER Big Blue 452D (s/n LL274149) 500 AMP, 5 KVA, 4000W w/ Deutz model F3L1011F diesel engine (s/n 3359/06)
Transformer: MARCUS type IW, 112.5 KVA, 600/415/240V, 50/60-HZ, 3-PH
DB (2): With breakers & outlets for (6) 100 AMP feeds to master skids plus (4) auxiliary
Welder: Bench, grinder, pipe vice, drill press, external oxygen & acetylene bottle racks
A/C Units (2): LG 1.5-TON capacity in cool store & safety container
Lights: Ten (10) 2-tube internal fluorescents and two (2) external 400W sodium vapor
Fire Extinguishers: Four (4) ABC
Hydraulic Jacks: ENERPAC hydraulic pump for 50-TON & 30-TON jacks




Cleaning Equipment

GRACO HP washdown units (2) with 28:1 air pumps
BRANDT MINIVACS (2) for OBM with 2" x 25'/50' KANALINE hoses, suction tubes and vacuum heads
CLEMCO type 2452 (s/n 0044) 200L, 0-12 Bar, sand blasting unit (shared with Rig-09)


Diesel Genset (Unit s/n NDSC-5232)

Engine: CAT D3306 DITA (s/n 85Z10817, a/n 7C 9312), 1500-RPM, 296-HP with WOODWARD type PRG governor

Alternator: CAT SR4 (s/n F5A07024), 400V, 1500-RPM, 244-KVA, 195-KW, 50-HZ

Fuel Tank: NSF 2m3 x 1.9mL x 1.4mW x 1.6mH x 0.9-T (JN 8017-04/08)


Motor Genset (Unit s/n NDSC-5234)
Motor: MARATHON 4J444T: 100-HP/600VAC/60HZ/1185RPM (s/n AE580153)

Alternator: NEWAGE model 350-28700, 415VAC, 50-HZ, 65 KW (Intersel 10/2006)





Rig Offices

ARABIAN INDUSTRIES air-conditioned, 4-office, laboratory, mess, storeroom with (6) cabins, each on 3-runner skid, mounted on two (2) 3-runner master skids with (2) independent 50-KW genset power supply sources:



Skid #1: - Toolpusher cabin with TP office (front) and Materialman (rear) with WC

- PE cabin with office, WC

- Client cabin with office, shower, bedroom. Installed: 10/2005



Skid #2: - Service Company cabin with (4) rooms (4 beds) e/w ablution (s/n NDSC-5270)

- Senior mess and CM/CE office

- 55m3 potable water tank with (2) pumps, filtration and chlorine injection



Skid #3: - Mud lab cabin with 1-man accommodation

- 2-room cabin with 2 beds for TP & PE

- Safety training cabin. Installed: 12/2005



Skid #4: CH MECH/ CH ELECT: Single skid 10.5mL x 3.5mW with furnished, WC/shower & bedroom. Installed: 2011





DP Bins (10): 37'L x 8'W on 3-runner skid (35-T SWL)

DC Bins (04): 37'L x 8'W on 3-runner skid (35-T SWL)

Junk Bins (3): 30'L x 7'W on 3-runner skid (35-T SWL)

Pipe Racks: 42"H x 27'L (8), 20"H x 27'L (8), 42"x13"L (2)

Seatainers (5): 20'L x 8'W x 8'H (10-T SWL)

Tool House: 27'L x 7' 10"W x 8"H on 3-runner skid.



Transport & Lifting

Crane: 30-TON mobile, all-terrain (AL-KHALIJ)

Forklift: CAT 4.8-TON (AL-KHALIJ)


TP: TOYOTA LANDCRUISER diesel wagon with stretcher (LT-30)

DSV: TOYOTA (PRADO) wagon (LT-55)

UTILITY: TOYOTA (HI-LUX) double cab diesel Pickup (LT-53)


Crew: TOYOTA 18-seater 2005 (HERTZ)





Mobile Camp

ARABIAN INDUSTRIES with (24) air-conditioned cabins, each on 3-runner skid, mounted on nine (9) 3-runner master skids.



Accomodation Rig & Camp

Rig Senior Staff: 9 Beds

Camp Senior Staff: 30 Beds

Camp Junior Staff: 68 Beds Total Beds: 107



M/Skid 1: (3) cabins: (6) senior rooms (24 beds)

M/Skid 2: (3) cabins: (4) senior rooms (8 beds) with center ablution & (2) junior (8 beds)

M/Skid 3: (3) cabins: (3) junior rooms (12 beds), (1) senior room (1 bed). Clinic-Medic room (2 beds including sick bay bed) with center ablution (2)

M/Skid 4: (3) cabins: (6) senior rooms (9 beds)

M/Skid 5: (3) cabins: (6) senior rooms (11 beds) with center ablution (1)

M/Skid 6: (3) cabins?2) junior rooms (8 beds), dry store, cold store

M/Skid 7: (3) cabins: senior mess, galley, junior mess ( up graded)

M/Skid 8: (3) cabins: ablution block, laundry, GRP water tank (55m3)

(2) cabins: 2 x 4-man JS sleeper

Mosque: 30'L x 10'W skidded with AC.



RO Unit: ECOWATER SYSTEMS model ESM-18CE (2.8m3/hour max output) with booster pump and model LBR8 UV sterilizer. Installed: 08/2004.



Skid 9 - Camp Generators:



Engines (2): CATERPILLAR model 3406 TA (S/N 2WBO2668/2WBO2667, A/N 4W3805), 1500 RPM, 362-HP, 270 kW with WOODWARD type PRG governor and fitted with crude oil heaters.
Generators (2): CATERPILLAR model SR-4 (S/N 6BA02075/6ba02080, A/N 5N8662), 1500-RPM, 300-KVA, 240-KW, 400VAC, 50-HZ, 433-AMP.


Electrical DB: Indent # DC61/4/30916 PDO-A1, Holec # 242.402-1985, System 3-PH, 4 wire, 414V - 50C/S rated operating voltage, 1200-AMP rated current main bussbars, 50KA - 1 SEC rated short-time withstand current, 110 KA rated peak withstand current, IP54 degree of protection.


Portable Air Compressor: ABAC Air Compressor 4 HP, Model: B3800-200CT3-V400CE.ABAC, (S/N. NDSC-5287), Manufacture date: 2008, Air End Model: 3700060, Manufacture date: 2007, powered by KEW Three Phase Induction motor, Type: Y90L-2, KW. 2.2, V.230/240, In Service: 04/2008.



Fuel Storage: 12,000L settling tank with 4,000L day-tank and transfer pump


Spare Diesel Genset (shared with all rigs)
Make: CAT skidded, soundproofed unit (s/n NDSC-5215)

Engine: CAT 3406B series (s/n 2WB 15217, a/n 9Y8247), 1500-RPM, 362-HP, 270-KW with WOODWARD type PRG governor

Alternator: CAT SR4, 400V, 1500-RPM, 300-KVA, 240-KW, 50-HZ, 433-AMP



Skid 10 - Camp Workshop

20'L x 8'W x 9'H sea container with shelves, workbench, vice, lights, AC and ABAC model B3800-200CT3-V400CE portable air compressor (lot #387066-0010) with model 3700060 air end (lot #016781-0299) and KEW 3-PH type Y90L-2 230/240V 2.2-KW 50-HZ induction motor (unit s/n NDSC-5287)



Guard Cabin: 18'L x 10'W X 8'H skid with 1.5-T air-conditioner.



Rig Mosque: 13'L x 10'W x 8'H skid with 1.5-T air-conditioner.





Training Room Equipment

PANASONIC model NV-MV22GCU VCR (s/n G5XA01514).
PANASONIC model PT-LC55E projector (s/n SL2240457).


RSTR Equipment

LENOVO type 0768 6VG laptop (s/n L3-D6959 06/06).
PENTAX model 9484271 digital camera.
Tape recorder.


BA Sets (22): DRAGER model PA-90, PA-94 MARINE: w/ 13 spare cylinders.

BA Sets (12): DRAGER model RAPID: 15 minute w/ 11 spare cylinders.

BA Sets (07): DRAGER model SAVER PP-15: 15 minute.



BA Recharging Compressor

BAUER Capitano model BCC-EI (s/n 8021).



Resuscitator

DRAGER w/ model Acute Pack 2001 oxygen cylinder with 2.51 O2 cylinder and accessories w/ (4 each) spare oxygen cylinders.



Fire Extinguishers (29): ANSUL type ABC 20 LBS. (at rig).

Fire Extinguishers (25): ANSUL type ABC 20 LBS. (at camp).

Fire Extinguishers (06): ANSUL type CO2 15 LBS. hand-held (3 ea rig & camp).

Fire Extinguishers (02): ANSUL type ABC 150 LBS. wheeled units.



Fire Pump (Rig)

GM 3-53 powered centrifugal w/ hoses/nozzles, STARTWELL model SDC-034 (s/n SE3192) inertia starter and separate Foam Generator unit driven by fire pump. Note: Rig engine replaced 04/2008 by John Deere Power Tec 4.5L 60-KW 2500 RPM (s/n PE 4045D653638).



Fire Pump (Camp)

LOMBARDINI model LOW 2204 60-HP 3000-RPM diesel engine (s/n 5351270) with electric start driving centrifugal pump.



Derrick Escape System: DBI-SALA ROLIGLISS model 3303015 (s/n 072440) with high speed manual retract. Installed: 03/2007.



Anti Fall Device (5): PROTECTA model AD-215AS with 50'L x 3/16" GI cable.



Derrickmans Harness (4): WEB DEVICES (p/n HA-855), semi rigid seat, full size dorsal D ring w/ 24" web ext, shoulder strap padding w/ parachute sliding bar adjuster, chest strap web ring w/ quick disconnect buckle, heavy duty grommeted leg straps, pre-formed padding for waist belt w/ lumbar D ring, semi rigid detachable & adjustable seat & web spider.



Man Riding Harness: WILLANS model T24 LE Harness Large CE-0120 (s/n 20268).



Cross-Over Style Harness (4): DBI-SALA (p/n 1102010) delta no-tangle design with spring-loaded stand-up back D ring, parachute buckles on lower shoulder straps, pass-thru-buckle leg straps, polyester webbing and plated hardware (ANSI Z359).



Shock Absorbing Lanyards (6): DBI-SALA (p/n 1220406) polyester twin lanyard (100% tie-off), 6'L w/ self locking snap hooks at end and each leg end.



Tie-Offs & Anchor: Pass thru adapter 3'L (p/n 1003000), 6'L (p/n 1003006) and choker style anchor 17"L to fit max 3" diameter.



Man-Riding Basket: 500 KG SWL (s/n NDSC-5006) with 5-T SWL pad eye tested to 10-T.

Recertified: ID/TEC 08/2005.



Ambient Gas Console

Sensor stations (5) & H2S console w/ UPS mounted in TP office (audible over Gaitronics PA system w/ rig floor visual alarms).



Gas Detector

MINIGAS-4 (OFCH): O2 0-25%, CH4 0-100% LEL, CO 0-999 PPM, H2S 0-499 PPM calibrated @ 10 PPM. Computer interface, log-view software, 240V mains adapter, charger, hand aspirator sampling assy w/ 5m hose & probe float.



Gas Monitors (12)

ZELLWGER Analytics model IMPULSE-XT personal H2S gas monitors (with two assigned to camp in Harweel, one with Harweel DS).



Other Safety Equipment:

Eyewash Stations (5): Model 750 portable gravity operated.
Chemical Shower: Mud mixing area.
First Aid: (3) kits
Windsocks: Orange cone
Anti-slip Mat: SAFETY PAD II around rotary.
Safety Cage: For rotary table, when master bushing removed.
Emergency Rescue Rod: Model CS-90 ISO, 5'L non conductive to 90KV CATU with insulated gloves located in PCR room.


Clinic Equipment:

Defibrillator: PRIMEDIC HeartSave AED Ser # 37154001552
ECG: BTL Industries BTL-08 MD3 Diagnostic ECG Ser # 08MD-0720991
Chlorometer: PALINTEST DUO 1000 digital meter (0.2 - 0.5 mg/l).
Stretcher #1: FERNO Scoop type model 65 (s/n L805897) with model 430 restraints.
Stretcher #2: Vehicle clinic type.
Stretcher #3: LECSAFE mast evacuation (s/n 99117133) w/ lift sling (s/n 99719965).
Stretcher #4: FERNO folding canvas type.
Stretcher #5: TOP Longmax clinic type.
WELDING TRANSFOMER - MILLER -GOLD STAR 402 -400 VOLT, 3 PHASE, 50 HZ,


FIRE ALARAM SYSTEM ; MODEL NO CFP 2/4/8/ ZONE CONVENTIONAL FIRE ALARM SYSTEM Connected to all the cabins in the camp site AND INSTALLED CONTROL PANEL IN THE SR MESS ROOM.INSTALLED MAY 2012


Full details to named buyers only.

Contact the Broker

Disclaimer: ALL DETAILS BELIEVED TO BE CORRECT BUT WITHOUT GUARANTEE - VESSEL OFFERED, AS IS, WHERE IS, SUBJECT TO PRIOR SALE, PRICE CHANGE, OR WITHDRAWAL WITHOUT NOTICE